Caterpillar Recalls

2013–2014 Caterpillar CT610, CT630, CT630LS and CT630S

The Linear Power Module (LPM) may potentially overheat following a voltage spike caused if the vehicles is jump start.

0 Caterpillar CT700-15L & 13L

Overseas models fitted with the same cabin are experiencing “de-lamination” of the sun visor supports which can lead to detachment of the visor.

0 Caterpillar CT700-15L SERIES

Under certain applications, heat generated by the engine may degrade air brake lines that are within close proximity to the turbocharger.

0 Caterpillar C15 truck engine

The Variable Valve Actuation (VVA) oil line may wear and cause an oil leak.

0 Caterpillar Wheel Loaders

Damage to the steering system from contamination.

0 Caterpillar Telehandlers

An internal seal within the 136-8537 Brake Booster may be defective which may allow the brake fluid to drain from the brake reservoir back to the hydraulic tank resulting in failure of the service brake system.

0 Caterpillar Track Type Loaders

Unexpected lift arm motion can occur if the shut-off valve is actuated with the engine running and the implement control lever in the 'float' detent position. Personal injury may result from unexpected lift arm movement.

0 Caterpillar Backhoe Loaders

Some roofs may have been made of material that can become brittle and crack. In rare instances, this has caused the roof to become unattached when trailering the machine.

0 Caterpillar Track Type Loader

Some roll over protection system (ROPS) support post material may have inconsistencies in the material that may cause the post to fail in a roll over situation.

0 Caterpillar Wheel Skidders

Improperly welded cab door screens have potential to allow large debris to enter through door.

0 Caterpillar Off Highway Trucks

The start relay and back-up relay wiring needs to be reworked to ensure the starting system is properly grounded.

0 Caterpillar Off Highway Trucks

The air start solenoid and back-up relay needs to be reworked to ensure the starting system is properly grounded.

0 Caterpillar Track Type Tractors and Loaders

The engine harness mounting may come into contact with the injector line which can result in fuel leakage under pressure and risk of fire.

0 Caterpillar Wheel Tractor Scrapers

The Roll-over Protection System Has Insufficient Weld Penetration. Structural Failure Could Result In Serious Injury Or Death In A Machine Rollover.

0 Caterpillar Telehandler Platforms

The Boom Speed May Be Too High To Meet Some Local Requirements.

0 Caterpillar Telehandlers

Due To A Manufacturing Process Problem A Certain Number Of Pilot Valve Assemblies May Have Been Installed That Contain A Defective Pin. Failure Of This Component Could Cause The Differential To Lock, Or The Work Tool To Malfunction.

0 Caterpillar G3612,G3616

The Hydrax supply and return oil lines support bracket clips may fail.

0 Caterpillar Wheel Skidders

PARKING BRAKE SUPPORT PLATE MAY LOOSEN WHICH MAY RESULT IN PARKING BRAKE MALFUNCTION.

0 Caterpillar Reclaimers, Mixers

Electrical Ecm Incorrectly Programmed Which May Cause The Makchine To Surge Forward Upon Startup.

0 Caterpillar Excavator

Starter Cable Interference Which May Result In Electrical Arc And /or Short Circuit.

0 Caterpillar Reclaimers

The Propel Speed Select, Steering Mode Select And Parking Brake Contact Blocks May Fail Under Certain Conditions.

0 Caterpillar 3116 MUI Truck Engines

Engine Rpm Instability Resulting In Engine Stalling At Low Idle Or Engine Surging.

0 Caterpillar Scrapers

The Brake Drums May Fail Resulting In Loss Of Braking Performance.

0 Caterpillar Compactors

Drive Shaft Bolts May Come Loose.

0 Caterpillar Backhoe

The Starting System May Fail Due To Moisture Ingress Into The Key Switch.

0 Caterpillar Generator Set

A Failure Of Internal Componentry Can Lead To The Failure Of The Entire Circuit Breaker If Tripped While Under Load, Possibly Leading To Hazard Of Electric Shock, Burn Or Explosion.

0 Caterpillar Telehandler

The Priority Valve Adaptor Needs To Be Changed As Under Certain Conditions During Rapid Steering A Temporary Loss Of Brakes And Hydraulic Functions May Occur.

0 Caterpillar Wheel Loaders

The Lift Cylinder Rod Could Experience A Weld Failure.

0 Caterpillar 515, 525 Skidders

The Service Brake May Fluctuate Out Of Specification Due To Cab Movement Which May Then Activate The Parking Brake During Operations On Some Machines.

0 Caterpillar 933

Voiding Of Lift And Multi-purpose Bucket Cylinder Resulting In Movement Of Lift Arms And/or Bucket Clam.

0 Caterpillar Scrapers

Welds On Brackets Of Seat Groups May Fatigue And Seat May Become Unstable.

0 Caterpillar 980G

Reversal Of 3rd Lever Implement Control When Updating Software Resulting In Implement Control Reversing.

0 Caterpillar 928g Loader, IT28G Carrier

The Cab Mounting Bolts May Need To Be Tightened.

0 Caterpillar 938F, IT38F

Steering System Is Difficult Or Hard To Steer In Rough Applications.

0 Caterpillar Motor Grader

The Shield Between The Engine And The Pumps Need To Be Extended As Oil May Spray Onto Engine.

0 Caterpillar Grader

A Hydraulic Hose May Rub On An Electrical Connector Resulting In Hydraulic Oil Leak And Electrical Short Circuit Could Occur.

0 Caterpillar 992G

Hydraulic Hose Bracket Can Break Resulting In Hydraulic Hose Hitting The Cab Window.

0 Caterpillar 3406B Engine

The Engine Governor May Fail To Control Engine Speed.